| Wago Main Page |
| I/O Products |
|
| Fieldbus Coupler |
| Programmable Feildbus Controller |
| Digital Input Modules |
| Digital Output Modules |
 |
| 1 Channel |
| 230V AC, 16A, relay 1a |
| 2 Channel |
| 24V DC,
0.5A |
| 24V DC, 2.0A |
| 24V DC,
0.5A, diagnostics |
| 24V DC,
2.0A, diagnostics |
| 24V DC,
EEx i |
| 125V AC,
0.5A, relay 2 CO contacts, pot. free |
| 230V AC,
1.0A relay 2 CO contacts, pot. free |
| 230V AC,
0.3A, solid state relay |
| 230V AC,
3.0A, solid state relay for 30s |
| 230V AC,
2.0A, relay 2 NO |
| 230V AC,
2.0A, relay 2 NO, pot. free |
| 4 Channel |
| 5V DC, 20
mA |
| 24V DC,
0.5A |
| 24V DC,
0.5A, 2-conductor |
| 24V DC,
0.5A, low-side switching |
| 8 Channel |
| 24V DC,
0.5A |
|
|
| Analog Input Modules |
| Analog Output Modules |
| Specialty Modules |
| System Modules |
| Approvals |
|
| Wago Digital Output Modules |
 |
| Part Number |
Conformity Marking |
Approvals |
 750-522 |
 |
cULus,
cULus-EX,
KEMA |
| 2-CHANNEL ANALOG OUTPUT MODULE AC 230 V CARRIER RAIL DIN 35 CAGE CLAMP CONNECTION |
| The digital output module controls actuators via semiconductor outputs. The bus module receives the control signal via a fieldbus coupler. The control of the outputs is fully isolated. The outputs are switched at the zero cross. The voltage supply of the outputs is made via the power jumper contacts. Each output has its own overload protection which is realized via an internal temperature limit. In case of an over-load, the bus module switches off the output. After the output connection has cooled down, it triggers the output again. The error bit reports the overload in the process image. The module is a 2-channel, 4-conductor device. Actuators with ground (earth) connection may be directly connected to the module. Attention: An additional supply module must be added for the supply of AC 230 V! |
|
| Technical Information |
| Characteristic |
Value |
| Number of outputs |
2 MAKE CONTACTS |
| Current consumption typ (internal) |
40 mA |
| Switching voltage |
AC 35 V ... 230 V |
| Switching current (nom) |
0.5 A per channel |
| Switching current (min) |
50 mA |
| Switching current (max) |
3 A (< 30 s operating time) each channel for a turn-on cycle of 1 hour |
| Peak current |
18 A (100 ms); 30 A (10 ms) |
| Max. switching frequency (kHz) |
0.05 kHz |
| Operating speed (typ) |
1.65 ms |
| Operating speed (max) |
15 ms |
| Leakage current (typ off) |
< 2,3 mA |
| Overvoltage protection |
AC 275 V (Varistor) |
| Isolation |
3 kV system / supply |
| Internal data width |
2 Bit In, 2 Bit Out |
| Operating temperature |
0 °C ... + 55 °C |
| Storage temperature |
-25 °C ... +85 °C |
| Relative air humidity |
95% |
| Vibration resistance |
acc. IEC 60068-2-6 |
| Shock resistance |
acc. IEC 60068-2-27 |
| Degree of protection |
IP 20 |
|
| Characteristic |
Value |
| EMC immunity to interference |
acc. EN 50082-2 (96) |
| EMC emission of interference |
per EN 50081-1 (93) |
| UL 508 |
E175199, UL 508 (applied for) |
| Conformity marking |
CE |
| Cross section from [mm²] |
0.08 mm² |
| Cross section to [mm²] |
2.5 mm² |
| Cross section from [AWG] |
28 AWG |
| Cross section to [AWG] |
14 AWG |
| Weight |
9.999 g |
| Color |
light gray |
| Height |
64 mm |
| Height |
2.52 in |
| Width |
24 mm |
| Width |
0.945 in |
| Depth |
100 mm |
| Depth |
3.937 in |
| Strip length from |
8 mm |
| Strip length to |
9 mm |
| Strip length |
0.33 in |
|
|
|
