| Wago Main Page |
| I/O Products |
|
| Fieldbus Coupler |
| Programmable Feildbus Controller |
| Digital Input Modules |
| Digital Output Modules |
 |
| 1 Channel |
| 230V AC, 16A, relay 1a |
| 2 Channel |
| 24V DC,
0.5A |
| 24V DC, 2.0A |
| 24V DC,
0.5A, diagnostics |
| 24V DC,
2.0A, diagnostics |
| 24V DC,
EEx i |
| 125V AC,
0.5A, relay 2 CO contacts, pot. free |
| 230V AC,
1.0A relay 2 CO contacts, pot. free |
| 230V AC,
0.3A, solid state relay |
| 230V AC,
3.0A, solid state relay for 30s |
| 230V AC,
2.0A, relay 2 NO |
| 230V AC,
2.0A, relay 2 NO, pot. free |
| 4 Channel |
| 5V DC, 20
mA |
| 24V DC,
0.5A |
| 24V DC,
0.5A, 2-conductor |
| 24V DC,
0.5A, low-side switching |
| 8 Channel |
| 24V DC,
0.5A |
|
|
| Analog Input Modules |
| Analog Output Modules |
| Specialty Modules |
| System Modules |
| Approvals |
|
| Wago Digital Output Modules |
 |
| Part Number |
Conformity Marking |
Approvals |
 750-514 |
 |
cULus,
KEMA |
| 2-CHANNEL RELAY OUTPUT MODULE AC 125 V, DC 30 V CARRIER RAIL DIN 35 CAGE CLAMP CONNECTION |
| The connected load is switched via the digital output (relay contact) from the control system. The internal system volt-age is used to trigger the relay. The SPDT contacts are electrically isolated. The switched status of the relay is shown by a LED. The module is a 2-channel device and actuators with a ground (earth) wire may be directly connected to the module. |
|
| Technical Information |
| Characteristic |
Value |
| Number of outputs |
2 CHANGEOVER CONTACTS (SPDT) |
| Current consumption typ (internal) |
70 mA |
| Switching voltage |
AC 125 V / DC 30 V |
| Switching power |
62.5 VA / 30 W |
| Switching current (max) |
AC 0.5 A / DC 1 A |
| Switching current (min) |
DC 0,01mA / 10mV |
| Max. switching frequency |
20 / min |
| Pull-in time max. |
4 ms |
| Drop-out time max. |
4 ms |
| Contact material |
Silver alloy, gold-plated |
| Mechanical life |
1 x 10^8 switching operations |
| Electrical life |
2 x 10^5 ( AC 0.5 A / 125 V) 5x 10 5 ( DC 1 A / 30 V) |
| Isolation |
1.5 kV EFF. (FIELD/SYSTEM), 2.5 kV RATED SURGE VOLTAGE; OVERVOLTAGE CATEGORY III |
| Internal data width (Bit) |
2 Bit |
| Operating temperature |
0 °C ... + 55 °C |
| Storage temperature |
-25 °C ... +85 °C |
| Relative air humidity |
95% |
| Vibration resistance |
acc. IEC 60068-2-6 |
| Shock resistance |
acc. IEC 60068-2-27 |
| Degree of protection |
IP 20 |
|
| Characteristic |
Value |
| EMC immunity to interference |
acc. EN 50082-2 (96) |
| EMC emission of interference |
per EN 50081-1 (93) |
| UL 508 |
E175199, UL 508 |
| KEMA |
01ATEX1024X Eex nA II T4 |
| Conformity marking |
CE |
| Cross section from [mm²] |
0.08 mm² |
| Cross section to [mm²] |
2.5 mm² |
| Cross section from [AWG] |
28 AWG |
| Cross section to [AWG] |
14 AWG |
| Voltage CSA |
125 V |
| Current rating CSA |
0,5 A |
| Weight |
49.5 g |
| Color |
light gray |
| Height |
64 mm |
| Height |
2.52 in |
| Width |
12 mm |
| Width |
0.472 in |
| Depth |
100 mm |
| Depth |
3.937 in |
| Strip length from |
8 mm |
| Strip length to |
9 mm |
| Strip length |
0.33 in |
|
|
|
